Some cyanide remains in the slurry after gold has been recovered, and many plants destroy most of it before tailings are discharged to the storage facility, both to protect wildlife and water and to meet licence conditions. The International Cyanide Management Code, for example, sets 50 mg/L of weak acid dissociable (WAD) cyanide as the limit in open water at tailings facilities for the protection of wildlife. Destruction oxidises cyanide to cyanate, a far less toxic compound that breaks down further over time. Sulphur dioxide with air, hydrogen peroxide and Caro's acid are the common oxidants, and each has a fixed stoichiometric requirement per gram of cyanide.
Cyanide destruction circuits are designed and operated from these stoichiometric ratios together with testwork. This article sets out the ratios, a worked example for the SO2/air process, and the controls that keep a detoxification circuit compliant.
SO2/air chemistry
where
- weak acid dissociable (WAD) cyanide to be destroyed; copper is the catalyst
- cyanate, far less toxic, which slowly breaks down further
- grams of sulphur dioxide per gram of cyanide (stoichiometric)
- grams of lime (as CaO) to neutralise the acid formed, per gram of cyanide
The reaction is fastest at a pH of about 8 to 9 with dissolved copper as a catalyst, and air supplies the oxygen. The sulphuric acid formed would lower the pH, so lime is added to hold it in range. Sulphur dioxide can be supplied as liquid SO2, by burning sulphur, or as sodium metabisulphite (SMBS, Na2S2O5), which releases two molecules of SO2 per molecule: 190.1 ÷ (2 × 64.07) = 1.48 g of SMBS per gram of SO2.
Iron cyanide complexes are removed as insoluble copper or zinc ferrocyanide precipitates. Thiocyanate is oxidised only slowly in this process.
Worked example
A CIL plant sends 600 m³/h of tailings solution containing 150 mg/L WAD cyanide (as CN) to detoxification. The cyanide to be destroyed is 600 × 150 ÷ 1,000 = 90 kg/h, and the stoichiometric SO2 requirement is 90 × 2.46 = 222 kg/h.
Testwork for this example set the operating ratio at 4 g SO2 per g CN, or 360 kg/h of SO2. Supplied as SMBS on a 100% basis, this is 360 × 1.48 = 534 kg/h, which is divided by the product purity to give the actual mass.
Lime to neutralise the acid formed by the cyanide reaction alone is 90 × 2.16 = 194 kg/h as CaO. Excess SO2 also forms acid, so actual lime consumption is higher, and lime addition is controlled on pH.
Copper sulphate is added if the tailings do not already contain sufficient dissolved copper, with the target set by testwork.
Hydrogen peroxide and Caro's acid
Hydrogen peroxide reacts as CN⁻ + H2O2 → OCN⁻ + H2O, with a theoretical requirement of 34.01 ÷ 26.02 = 1.31 g H2O2 per g CN. It is most effective on solutions or low-solids streams, often with a copper catalyst.
Caro's acid (peroxymonosulphuric acid, H2SO5) is produced on site by mixing concentrated sulphuric acid with hydrogen peroxide, and reacts as CN⁻ + H2SO5 → OCN⁻ + H2SO4, with a theoretical requirement of 114.08 ÷ 26.02 = 4.38 g H2SO5 per g CN. Its fast reaction suits slurries, but the acid it carries and forms must be neutralised with lime.
Setting the dose by testwork
- Collect representative tailings slurry and solution.
- Run batch or continuous tests over a range of reagent ratios, pH values, copper doses and residence times.
- Measure WAD and total cyanide, copper, pH and dissolved oxygen in the treated product.
- Select the lowest reagent ratio that reliably meets the target with a margin, and confirm the reactor residence time.
Circuit operation
WAD cyanide in the detoxification feed and discharge should be measured every shift, with an online analyser where one is available. The SO2 or SMBS dose should be controlled in proportion to the cyanide load, calculated as flow multiplied by concentration, rather than at a fixed rate.
pH should be held in the optimum range with lime, since low pH risks the release of hydrogen cyanide gas and high pH slows the reaction. The reactor must be well aerated and agitated, because oxygen supply is often the actual limit on performance.
The most economical form of detoxification is reducing the cyanide load in the first place, by optimising cyanide addition in the leach.
Glossary
- Detox
- Short for cyanide destruction: oxidising cyanide in tailings before disposal.
- WAD cyanide
- Weak acid dissociable cyanide: free cyanide and cyanide in weak and moderately strong metal complexes.
- Cyanate
- OCN⁻, the much less toxic product of cyanide oxidation.
- SMBS
- Sodium metabisulphite, Na2S2O5, a solid source of sulphur dioxide.
- Caro's acid
- Peroxymonosulphuric acid, H2SO5, a strong oxidant made from sulphuric acid and hydrogen peroxide.
- Catalyst
- A substance that speeds a reaction without being consumed; copper in the SO2/air process.
- Stoichiometric
- The exact amount of reagent the chemical equation requires.
Frequently asked questions
How much SO2 is needed to destroy cyanide?
In theory 2.46 g of SO2 per gram of WAD cyanide. Plants use more, at a ratio set by testwork, because other species also consume SO2.
How much SMBS replaces one kilogram of SO2?
About 1.48 kg of pure sodium metabisulphite, because each molecule releases two molecules of SO2. The figure is divided by the product purity to give the actual mass.
What pH is best for the SO2/air process?
About 8 to 9, maintained with lime.
How much hydrogen peroxide does cyanide destruction need?
In theory 1.31 g of H2O2 per gram of cyanide. Actual consumption is set by testwork.
Discuss your plant with a metallurgist
Tiegel is a Perth metallurgy company. We help with testwork, plant optimisation, metal accounting and investigations, and we build the Tiegel Suite software.
Talk to a metallurgistReferences and further reading
- Mudder, T.I., Botz, M.M. and Smith, A. (2001). Chemistry and Treatment of Cyanidation Wastes, 2nd edition. Mining Journal Books.
- Marsden, J.O. and House, C.I. (2006). The Chemistry of Gold Extraction, 2nd edition. Society for Mining, Metallurgy and Exploration.
- International Cyanide Management Institute. International Cyanide Management Code. Link
Worked examples and charts marked illustrative use invented figures, not data from any operation.