Tiegel home Talk to a metallurgist

Flotation reagents and froth: collectors, frothers, modifiers and gas dispersion

The function of collectors, frothers and modifiers, the measurement of superficial gas velocity and bubble surface area flux, and the effect of the froth on recovery.

· 6 minute read · By

Flotation separates minerals on differences in surface wettability. Most mineral surfaces are wetted by water and would remain in the pulp. A collector adsorbs on the valuable mineral and makes its surface hydrophobic, so that the particles attach to air bubbles, rise to the surface and form a froth that overflows as concentrate.

Other reagents support the collector. Frothers produce small bubbles and a froth stable enough to carry the mineral load. Modifiers adjust the pulp chemistry so that the collector adsorbs on the intended mineral and not on the gangue. The gas supply is as important as the chemistry: both the air rate and the bubble size affect the flotation rate.

This article describes the function of each reagent group, the measurement of gas dispersion in a cell, and the effect of the froth on grade and recovery. Dose rates in g/t and pump settings are covered in Reagent dosing: g/t to pump flow.

How a collector makes a mineral floatCollector molecules attach by their polar head to the valuable mineral surface, leaving their hydrocarbon tails pointing outward; the water-repellent surface sticks to an air bubble. Gangue without collector stays wetted.valuable mineral surfaceair bubbleattaches to thewater-repellent surfacepolar head bonds to the mineralhydrocarbon tail faces the watergangue: no collectorstays wet and sinks
Collectors make the chosen mineral water-repellent so bubbles can pick it up. Modifiers decide which minerals the collector coats; frothers keep the bubbles small and the froth stable.

Reagent groups

GroupFunctionCommon examples
Collectors for sulphidesAdsorb on sulphide minerals and make them water-repellentXanthates (such as SIBX and PAX), dithiophosphates, thionocarbamates
Collectors for oxides and silicatesAdsorb on non-sulphide mineralsFatty acids, used for example on spodumene; amines, used for example on quartz in reverse flotation of iron ore
FrothersProduce small bubbles and a froth stable enough to carry the load, then break down in the launderMIBC, polyglycols and glycol ethers
pH modifiersSet the pH, which controls collector attachment and which minerals floatLime, soda ash, sulphuric acid
DepressantsPrevent unwanted minerals from floatingLime and cyanide for pyrite, polysaccharides such as CMC and guar for talc, sodium silicate for silicates
ActivatorsEnable a mineral to float that otherwise would notCopper sulphate for sphalerite; sodium hydrosulphide to sulphidise oxidised copper and lead minerals
DispersantsPrevent fine slimes from coating other particlesSodium silicate, polyphosphates

Reagent schemes are specific to each ore. They are developed in laboratory testwork and refined on the plant. Additional collector does not always improve performance: beyond a certain addition it floats more gangue and lowers the concentrate grade. Excess frother produces a froth so stable that it carries water and fine gangue over the lip.

Mass pull and enrichment ratio

mass pull=f−tc−tenrichment ratio=cf

where

f, c, t
feed, concentrate and tailings grades (%)
mass pull
concentrate mass as a fraction of feed mass

Worked example: a rougher feed of 0.80% copper gives a concentrate of 24% and a tailing of 0.10%. The mass pull is (0.80 − 0.10) ÷ (24 − 0.10) = 2.9% of the feed, the enrichment ratio is 24 ÷ 0.80 = 30, and the recovery is 24 × 0.70 ÷ (0.80 × 23.9) = 87.9%. The two-product recovery calculator performs this calculation from the three assays. Mass pull should be tracked every shift: an increase in mass pull without a corresponding increase in recovery usually indicates that gangue is floating.

Gas dispersion: Jg, bubble size and Sb

Air is effectively a reagent in a flotation cell. Two measurements describe it: the volume of air passing upward through each square metre of cell cross-section, known as the superficial gas velocity (Jg), and the bubble size. Together they give the bubble surface area flux, Sb, which is the total bubble surface rising through the cell each second and therefore the surface available for particle collision.

Jg=QgASb=6Jgd32k=P×Sb×Rf

where

Jg
superficial gas velocity: air flow per unit cross-sectional area of the cell (m/s, often quoted in cm/s)
Qg, A
air flow rate (m³/s) and cell cross-sectional area (m²)
Sb
bubble surface area flux: bubble surface passing through each square metre of the cell every second (s⁻¹)
d32
Sauter mean bubble diameter (m)
k
flotation rate constant (min⁻¹ or s⁻¹)
P
floatability of the mineral, which reagents control
Rf
froth recovery: the fraction of attached particles that survive the froth and report to concentrate

Worked example: a cell with a cross-section of 14 m² receives 0.25 m³/s of air. Jg = 0.25 ÷ 14 = 0.0179 m/s, or 1.79 cm/s. With a Sauter mean bubble size of 1.5 mm, Sb = 6 × 0.0179 ÷ 0.0015 = 71 s⁻¹. Halving the bubble size at the same air rate doubles Sb, which is one reason that frother addition and impeller condition have such a large effect on performance.

Gas dispersion is measured with a Jg probe, a tube that collects the rising air over a known area, and a bubble viewer, a sampling tube in which the bubbles are photographed. Surveys of a complete bank often show cells operating at very different Jg because of worn impellers, blocked air lines or mismatched air valve settings. These faults are usually quick and inexpensive to correct.

The froth zone

Recovery pathways in a flotation cellParticles attach to bubbles in the pulp zone and rise into the froth. Some drop back as the froth drains. Fine particles are also carried up in the water between bubbles, which is called entrainment.FeedpulpPulp zonecollision and attachmentFroth zonedrainage and coalescenceConcentrateover the lipTailingsdrop-backattached particles riseentrainment: fine gangue rises with the water between bubbles and dilutes the grade
Overall recovery depends on what happens in both zones: collection in the pulp, then how much survives the froth. Water recovery drives the unwanted entrainment of fine gangue.

Not every particle that reaches the froth reports to the launder. Bubbles burst and coalesce as the froth ages, and attached particles drop back into the pulp. The proportion that survives is the froth recovery, and a deep froth with a long residence time loses more. Water also drains through the froth and carries fine particles in both directions. Fine gangue that rises with the water between bubbles is known as entrainment; it lowers concentrate grade and correlates closely with water recovery.

Ca=concentrate solids (t/h)froth surface area (m²)

where

Ca
carrying rate (t/h per m²): how hard the froth is being worked to carry concentrate

The practical controls on the froth are pulp level (which sets froth depth), air rate, frother addition and, in columns and some cleaner cells, wash water sprayed onto the froth to return entrained gangue to the pulp. A deeper froth or wash water raises grade at some cost to recovery, and the appropriate balance is established by surveys and plant trials.

Glossary

Collector
A reagent that adsorbs on a chosen mineral and makes its surface water-repellent so it attaches to bubbles.
Frother
A reagent that makes small bubbles and a stable froth.
Depressant
A reagent that stops a mineral from floating.
Activator
A reagent that changes a mineral's surface so the collector can attach.
Superficial gas velocity (Jg)
Air flow divided by cell cross-sectional area.
Bubble surface area flux (Sb)
Bubble surface rising through each square metre of cell per second; 6Jg divided by the Sauter mean bubble diameter.
Froth recovery
The fraction of particles entering the froth attached to bubbles that reach the concentrate.
Entrainment
Fine particles carried into the concentrate with water rather than by attachment to bubbles.

Frequently asked questions

What is the difference between a collector and a frother?

A collector adsorbs on the mineral so that it attaches to bubbles. A frother acts on the bubbles and the froth, making them small and stable. Some reagents have a minor effect of both kinds.

How much collector should be added?

Enough to float the valuable mineral at an acceptable grade, as determined by laboratory testwork and plant trials. Sulphide collector additions are usually tens of grams per tonne, but each ore is different.

Why measure bubble surface area flux?

The flotation rate constant increases with Sb. Two cells with the same air rate can perform very differently if their bubble sizes differ.

Why does concentrate grade fall when more frother is added?

A more stable froth holds more water, and the additional water carries fine gangue into the concentrate by entrainment.

Discuss your plant with a metallurgist

Tiegel is a Perth metallurgy company. We help with testwork, plant optimisation, metal accounting and investigations, and we build the Tiegel Suite software.

Talk to a metallurgist

References and further reading

  1. Wills, B.A. and Finch, J.A. (2016). Wills' Mineral Processing Technology, 8th edition. Butterworth-Heinemann. Chapter 12, Froth flotation.
  2. Gorain, B.K., Franzidis, J.-P. and Manlapig, E.V. (1997). Studies on impeller type, impeller speed and air flow rate in an industrial scale flotation cell. Part 4: Effect of bubble surface area flux on flotation performance. Minerals Engineering, 10(4), 367–379.
  3. Bubble surface area flux: a parameter to characterize flotation cells. OneMine. Link

Worked examples and charts marked illustrative use invented figures, not data from any operation.