Tiegel home Talk to a metallurgist

Dissolved oxygen in gold cyanidation: its effect on leach rate and how to control it

Why dissolved oxygen often limits the rate of gold cyanidation, the cyanide-to-oxygen ratio, the main oxygen consumers in a leach, and how plants measure and raise DO.

· 4 minute read · By

Cyanide receives most of the attention in a leach circuit, but gold does not dissolve without oxygen. In many plants the leach rate is limited not by cyanide but by the supply of oxygen to the gold surface. Increasing cyanide in that situation adds cost with little benefit.

Dissolution chemistry

Oxygen and cyanide reaching a gold surfaceDissolved oxygen and free cyanide diffuse through a thin liquid layer to the gold surface; aurocyanide diffuses away.Gold particle surfacethin liquid layer at the surfaceO₂ (dissolved oxygen)CN⁻ (free cyanide)Au(CN)₂⁻ (dissolved gold)The slower of the two supplies, oxygen or cyanide, sets the leach rate.
Both oxygen and cyanide must reach the gold surface for it to dissolve. Because water holds little oxygen, oxygen is often the slower supply.

The overall reaction for the dissolution of gold in cyanide is Elsner's equation:

4Au+8CN−+O2+2H2O→4Au(CN)2−+4OH−

where

Au
gold metal
CN−
free cyanide ion
O2
dissolved oxygen
Au(CN)2−
aurocyanide, the dissolved gold complex adsorbed by carbon

Oxygen is the oxidant, and cyanide holds the dissolved gold in solution. Both must reach the gold surface, so the slower of the two supplies sets the rate.

Oxygen solubility in leach pulp

Oxygen is only slightly soluble in water. Fresh water in equilibrium with air at 25 °C holds about 8.2 mg/L, and this limit falls with rising temperature, at altitude where air pressure is lower, and with increasing dissolved salt. Salinity is significant in Western Australia, where many plants operate on saline or hypersaline bore water. Using pure oxygen instead of air raises the limit several-fold, because the partial pressure of oxygen in the gas is much higher.

Oxygen solubility versus temperatureAir-saturated fresh water holds about 11.3 mg/L at 10 °C, 8.3 mg/L at 25 °C and 5.9 mg/L at 45 °C.567891011121015202530354045Temperature (°C)Dissolved oxygen at saturation (mg/L)Air-saturated fresh water: 10 → 11Air-saturated fresh water: 15 → 10Air-saturated fresh water: 20 → 9Air-saturated fresh water: 25 → 8Air-saturated fresh water: 30 → 8Air-saturated fresh water: 35 → 7Air-saturated fresh water: 40 → 6Air-saturated fresh water: 45 → 6Fresh water, air
Dissolved oxygen at saturation with air, fresh water at sea-level pressure, from the Benson and Krause equation. Saline water and altitude lower these values further.

The cyanide-to-oxygen ratio

Because both reagents must reach the gold surface, their ratio is what matters. Rumball and Houchin reported an optimum for oxide ores of about 106 mg/L NaCN to 10 mg/L dissolved oxygen, or 6.9 to 1 on a molar basis. They also found that ores with conductive sulphides in contact with the gold require a higher ratio and can leach at lower dissolved oxygen.

Where free cyanide is well above the level that the available oxygen can match, the leach is oxygen-limited. Further cyanide additions waste reagent and increase the detoxification load, whereas raising DO increases the leach rate.

Oxygen consumers in the leach

Reactive sulphides are the principal consumers. Pyrrhotite and some other sulphides oxidise readily and can deplete oxygen in the first tanks, while also consuming cyanide. Ferrous iron and other reduced species in the pulp or process water also consume oxygen, and high pulp density and long pipelines reduce oxygen transfer before the pulp reaches the leach.

Low DO in the first tank, recovering further down the train, indicates that the ore is consuming oxygen faster than it is supplied. A pre-aeration stage ahead of cyanide addition is a common means of satisfying that demand before leaching begins.

Dissolved oxygen down a leach trainWithout pre-aeration DO is low in the first tank where reactive sulphides consume oxygen; with pre-aeration it is close to target from the start.0369123456Tank numberDissolved oxygen (mg/L)No pre-aerationWith pre-aerationNo pre-aeration: 1 → 4No pre-aeration: 2 → 5No pre-aeration: 3 → 7No pre-aeration: 4 → 7No pre-aeration: 5 → 7No pre-aeration: 6 → 7No pre-aerationWith pre-aeration: 1 → 7With pre-aeration: 2 → 7With pre-aeration: 3 → 7With pre-aeration: 4 → 7With pre-aeration: 5 → 8With pre-aeration: 6 → 8With pre-aeration
A DO profile down the train shows where oxygen demand is. Low DO in the first tank, recovering further down, points to oxygen-hungry ore. Illustrative figures.

Methods of raising DO

Air sparging, through the agitator shaft or through spargers, is the least expensive method, but it cannot exceed air saturation. Oxygen injection, from an on-site oxygen plant or from liquid oxygen, achieves much higher DO and is the basis of carbon-in-leach practice with oxygen. Hydrogen peroxide dosing is used where oxygen supply is constrained or as a short-term measure, and high-shear injection systems improve gas transfer into dense pulp.

Whichever method is used, the objective is a stable DO target in each tank, set from testwork, rather than the maximum achievable oxygen level.

Measuring DO

DO should be measured in every tank, not only the first, because the profile along the train shows where the oxygen demand lies.

Probes in slurry foul and drift, so regular cleaning and calibration are essential; a reading that never changes should be treated as a fault rather than a stable result. Probe readings should be checked with a portable meter at a consistent depth and location, away from spargers.

DO is best interpreted alongside gold. When DO and free cyanide profiles are plotted with the solution gold profile, a leach that slows where DO falls indicates that oxygen is the limiting factor.

Saldora can display DO and cyanide readings from SCADA on each tank of a live flowsheet. Our article on CIL and CIP describes how to distinguish a leaching problem from an adsorption problem.

Glossary

Dissolved oxygen (DO)
Oxygen gas dissolved in the slurry water, measured in mg/L.
Oxidant
A substance that takes electrons from another, allowing gold to dissolve.
Free cyanide
Cyanide in solution that is available to dissolve gold.
Solubility
The most of a gas or solid that a liquid can hold at a given temperature and pressure.
Sparging
Bubbling air or oxygen into a tank.
Pre-aeration
Aerating the slurry before cyanide is added, to satisfy oxygen-hungry minerals first.
Pyrrhotite
An iron sulphide mineral that reacts readily and consumes oxygen and cyanide.
Saline water
Process water with a high dissolved salt content, which holds less oxygen.

Frequently asked questions

How can I tell whether my leach is oxygen-limited?

If free cyanide is well above the level the available oxygen can match, DO is low in the early tanks, and additional cyanide does not improve recovery, oxygen is likely to be the limit.

Is more oxygen always better?

No. Above the level the reaction requires, additional oxygen adds cost without benefit. The target should be set from testwork.

Why is DO lower in the first tank?

Fresh ore meets the slurry there, and reactive minerals consume oxygen most rapidly at that point.

Does water temperature or salinity matter?

Yes. Both reduce the amount of oxygen water can hold, so plants on saline water or in hot climates often need oxygen injection to reach the same DO.

Discuss your plant with a metallurgist

Tiegel is a Perth metallurgy company. We help with testwork, plant optimisation, metal accounting and investigations, and we build the Tiegel Suite software.

Talk to a metallurgist

References and further reading

  1. Rumball, J.A. and Houchin, M.R. (2003). Cyanide: oxygen ratio for leaching gold in sulphide ores. International Mineral Processing Congress. Link
  2. Oxygen solubility in fresh water at 25 °C: 8.24 mg/L. BioNumbers, citing Vesilind, P.A. (1996), Introduction to Environmental Engineering. Link
  3. Marsden, J.O. and House, C.I. (2006). The Chemistry of Gold Extraction, 2nd edition. Society for Mining, Metallurgy and Exploration.

Worked examples and charts marked illustrative use invented figures, not data from any operation.