Hard-rock lithium is mined from pegmatites in which the principal lithium mineral is spodumene, accompanied by quartz, feldspar and mica. Pure spodumene contains about 8.0% Li₂O. A concentrator aims to produce a concentrate of about 6% Li₂O, often referred to as SC6, with iron low enough to meet the requirements of the converter that buys it. Two properties make the separation possible: spodumene is denser than the associated minerals, which dense media separation exploits on coarse particles, and its surface can be made hydrophobic with a suitable collector, which flotation exploits on fine particles. Western Australia produces much of the world's spodumene concentrate, so these circuits account for a large share of the state's processing work.
Dense media separation and flotation by particle size
Spodumene has a specific gravity of about 3.1 to 3.2, noticeably higher than quartz and feldspar. Dense media separation (DMS) is therefore effective on coarse particles, roughly above 0.85 mm, provided the spodumene is liberated at that size. Below that size DMS loses efficiency, and flotation is used for particles finer than about 300 µm.
Most plants therefore split the crushed ore by size, with the coarse fractions treated by DMS and the fines by flotation, in proportions that depend on the liberation characteristics of the ore. Ore sorting is also used at coarse sizes to reject waste rock and iron-bearing material early in the circuit.
Flotation feed preparation
Spodumene flotation is sensitive to surface condition, so feed preparation is as important as reagent selection. The industrial sequence described in the literature is as follows:
- Grinding to liberate spodumene from gangue.
- Scrubbing with caustic soda (NaOH) to clean and activate the spodumene surfaces.
- Desliming to remove the finest particles, typically below about 15 to 20 µm, since slimes consume collector and carry gangue into the froth by entrainment.
- Conditioning with the collector at high density, often around 55 to 60% solids.
Collector and pH
Fatty acids are the principal spodumene collectors. Tall oil fatty acids are the most common industrial choice, while oleic acid and sodium oleate dominate the research literature. A review by Cook and Gibson describes typical practice as 500 to 750 g/t of fatty acid collector at pH 7.5 to 8.5. Fatty acid behaviour changes sharply with pH in this range, so pH control is essential.
Dissolved metal ions are also significant. Calcium, magnesium and ferric ions can activate spodumene, but they can also activate gangue. Changes in process water chemistry, for example a new bore field or a higher proportion of recycled water, can alter flotation performance without any change in the ore.
Gangue minerals and the iron limit
The common gangue minerals are feldspars, quartz and micas, together with iron-bearing silicates such as amphiboles and pyroxenes. The iron silicates are the most difficult to reject, because they respond to fatty acids in much the same way as spodumene. Battery-grade concentrate specifications call for more than 6.0% Li₂O and less than 1.0% Fe₂O₃, while technical grades for glass and ceramics require much lower iron.
Magnetic separation is used at several points to control iron, on the DMS or flotation feed and on the final concentrate. If concentrate iron rises, the magnetic separators and the iron-silicate content of the ore should be checked before flotation reagents are changed.
Diagnosing changes in flotation performance
An increase in slimes, from a change of ore type or from weathered ore, raises collector demand and entrainment, so desliming cyclone performance is the first item to check. Water hardness and dissolved ions alter collector behaviour and activation. Low conditioning density reduces collector adsorption on spodumene, and even a small drift in pH can change collector speciation enough to affect grade and recovery. The grind also matters: a coarser flotation feed lowers liberation and recovery, while a finer feed generates more slimes.
Ajax includes size and density separation, flotation and magnetic separation among its unit models, so a DMS and flotation split can be modelled as one circuit. Saldora can track daily Li₂O and Fe₂O₃ grades and recoveries through to the month-end report.
Glossary
- Spodumene
- A lithium aluminium silicate mineral, the main lithium mineral in Western Australian hard-rock deposits.
- Pegmatite
- A coarse-grained igneous rock that can host spodumene.
- SC6
- Spodumene concentrate at about 6% Li₂O, the common traded product.
- Li₂O
- Lithium oxide; lithium grades are quoted as % Li₂O.
- Dense media separation (DMS)
- Separating particles by density in a heavy liquid suspension, used on coarse spodumene.
- Flotation
- Separating particles by making the valuable mineral water-repellent so it attaches to air bubbles and rises.
- Collector
- A chemical that makes a mineral's surface water-repellent; fatty acids for spodumene.
- Desliming
- Removing the finest particles before flotation.
- Gangue
- The worthless minerals in the ore.
Frequently asked questions
Why do spodumene plants use both DMS and flotation?
Each process works best at a different particle size. DMS separates coarse particles, while flotation treats the fine particles that DMS cannot.
What does 6% Li₂O mean?
Six per cent of the concentrate's mass is lithium oxide. Pure spodumene is about 8.0% Li₂O, so a 6% concentrate is roughly three-quarters spodumene.
Why is iron important?
Converters set limits on iron in concentrate. Iron-bearing minerals float in much the same way as spodumene, so magnetic separation is used to remove them.
Why does water quality affect flotation?
Dissolved calcium, magnesium and iron change the behaviour of the fatty acid collector and the minerals to which it attaches.
Discuss your plant with a metallurgist
Tiegel is a Perth metallurgy company. We help with testwork, plant optimisation, metal accounting and investigations, and we build the Tiegel Suite software.
Talk to a metallurgistReferences and further reading
- Cook, B.K. and Gibson, C.E. (2023). A review of fatty acid collectors: implications for spodumene flotation. Minerals, 13(2), 212. Link
- An overview of spodumene beneficiation. OneMine. Link
- Selective flotation of fine spodumene with anionic polyacrylamide flocculant and calcium activator. AusIMM Critical Minerals Conference 2025. Link
Worked examples and charts marked illustrative use invented figures, not data from any operation.