In solvent extraction, an organic phase containing an extractant selective for the target metal is mixed with the aqueous leach solution, and the metal transfers into the organic. After the phases separate, the loaded organic is contacted with strong acid, which returns the metal to a small volume of clean aqueous solution for electrowinning. A single contact does not transfer all of the metal, so plants use several mixer-settlers in series with the two phases flowing counter-current, and the McCabe-Thiele diagram is the graphical method used to determine how many stages are required.
Solvent extraction is central to copper heap and agitated leach plants and is also used for uranium, cobalt, nickel, rare earths and lithium refining. This article explains the two curves that underlie every SX design and works through a copper example.
The extraction isotherm
An isotherm is measured in the laboratory by contacting organic and aqueous solutions at a range of organic-to-aqueous ratios, allowing them to reach equilibrium, and measuring the metal in each phase. The points form a curve: at low aqueous concentrations the organic loading rises steeply, and at high concentrations it approaches its maximum.
where
- distribution coefficient at equilibrium
- ,
- metal in aqueous and in organic (g/L)
- metal in the stripped organic entering extraction (g/L)
- metal in the raffinate leaving extraction (g/L)
- ratio of aqueous to organic flow
In the worked example, the isotherm for the organic used is approximated by y = 6.0x ÷ (0.3 + x), with x and y in g/L copper. At the feed concentration of 3.0 g/L, the organic could load to a maximum of 5.45 g/L.
The operating line
In a counter-current extraction circuit, the aqueous phase enters stage E1 and leaves stage E2 as raffinate, while the stripped organic enters E2 and leaves E1 loaded. A copper balance gives the operating line, a straight line of slope A/O through the points (raffinate, stripped organic) and (feed, loaded organic).
Worked example: feed 3.0 g/L copper, stripped organic 1.8 g/L, A/O = 1.
The McCabe-Thiele construction
- Plot the isotherm and the operating line on the same axes, with aqueous concentration on x and organic concentration on y.
- Start at the feed end, at the point (3.0, loaded organic) on the operating line.
- Step horizontally to the isotherm. This is stage E1, where the organic leaving at the loaded value is in equilibrium with the aqueous leaving E1.
- Step vertically down to the operating line, which gives the organic entering E1 from E2.
- Repeat until the aqueous concentration falls to the target raffinate. The number of steps is the number of theoretical stages.
For two theoretical stages, the construction closes at a raffinate of 0.22 g/L and a loaded organic of 4.58 g/L, with 0.97 g/L in the aqueous leaving E1. Extraction = (3.0 − 0.22) ÷ 3.0 = 92.6%. The organic carries a net 4.58 − 1.80 = 2.78 g/L of copper to the strip circuit, and the loaded organic is at 84% of the 5.45 g/L maximum, which leaves an appropriate margin.
The same construction applies to stripping, using the strip isotherm and the strip operating line.
Design and operating variables
The A/O ratio sets the slope of the operating line. More organic per unit of aqueous (a lower A/O) gives a flatter line and either fewer stages or a lower raffinate, at the cost of lower organic loading and a larger organic inventory. Extractant concentration raises the isotherm and the maximum loading, at higher cost and viscosity. Better stripping, giving lower copper in the stripped organic, lowers the starting point of the operating line and the raffinate achievable.
For copper oxime extractants, extraction releases acid and weakens as pH falls, so the pH of the leach solution affects the isotherm. Real mixer-settlers reach perhaps 90 to 95% of equilibrium per stage, and designs allow for this stage efficiency. Entrainment of organic in the raffinate and of aqueous into the strip circuit, together with crud formation, increases cost and contaminates the electrolyte; settler design and correct phase continuity control them.
Glossary
- Solvent extraction
- Transferring a metal between an aqueous solution and an immiscible organic phase.
- Extractant
- The chemical in the organic phase that binds the metal.
- Isotherm
- The equilibrium relationship between metal in the organic and metal in the aqueous.
- Operating line
- The mass balance line on a McCabe-Thiele diagram; its slope is the A/O flow ratio.
- Raffinate
- The aqueous solution leaving extraction, depleted of metal.
- Loaded and stripped organic
- Organic leaving extraction carrying metal, and organic leaving stripping with little metal.
- Mixer-settler
- A box where the phases are mixed then allowed to separate.
- Crud
- A stable emulsion of solids, organic and aqueous that forms at the interface.
Frequently asked questions
What is a McCabe-Thiele diagram?
A plot of metal in the organic against metal in the aqueous phase, showing the equilibrium isotherm and the mass balance operating line. The steps between them give the number of theoretical stages.
How is extraction calculated in SX?
Feed concentration minus raffinate concentration, divided by feed concentration.
What is the effect of the A/O ratio?
It sets the slope of the operating line. More organic per unit of aqueous lowers the raffinate for a given number of stages but reduces organic loading.
Why do real circuits need more stages than the diagram shows?
Mixer-settlers do not reach full equilibrium, so each real stage achieves less than a theoretical stage.
Discuss your plant with a metallurgist
Tiegel is a Perth metallurgy company. We help with testwork, plant optimisation, metal accounting and investigations, and we build the Tiegel Suite software.
Talk to a metallurgistReferences and further reading
- Ritcey, G.M. and Ashbrook, A.W. (1984). Solvent Extraction: Principles and Applications to Process Metallurgy, Part I. Elsevier.
- Schlesinger, M.E., King, M.J., Sole, K.C. and Davenport, W.G. (2011). Extractive Metallurgy of Copper, 5th edition. Elsevier.
Worked examples and charts marked illustrative use invented figures, not data from any operation.