Tiegel home Talk to a metallurgist

Electrowinning calculations: Faraday's law, current efficiency and specific energy

Faraday's law, current efficiency and energy per kilogram for electrowinning, with worked examples for a gold cell and a copper tankhouse cell.

· 5 minute read · By

In electrowinning, a rectifier supplies direct current to a cell containing metal-bearing solution. Current enters through the anodes and leaves through the cathodes, where dissolved metal ions are reduced and deposited, either on plates or, in gold cells, on steel wool or mesh. Each gold ion requires one electron and each copper ion two, so the charge passed sets an upper limit on the metal that can be deposited. In practice part of the current drives other reactions, such as the reduction of water to hydrogen, and the fraction that deposits metal is the current efficiency.

Electrowinning is the final recovery step in gold plants, after carbon elution, and in copper solvent extraction plants. The core calculations are the same in both: Faraday's law, current efficiency and specific energy. This article works through them with one gold example and one copper example.

Electrowinning cellElectrolyte flows through a cell between anodes and cathodes; direct current from a rectifier plates metal on the cathodes and evolves oxygen at the anodes.anodes (+)cathodes (−)Rectifier (DC)Rich electrolyteSpent electrolyteMetal ions take electrons at the cathode and plate out; water is split at the anode
An electrowinning cell. Every electron from the rectifier does one job at the cathode: plate metal, or drive a side reaction such as making hydrogen or reducing oxygen.

Faraday's law

m=I×t×Mn×F×η

where

m
mass of metal plated (g)
I, t
current (A) and time (s); use 3600 × hours
M
molar mass of the metal (g/mol): gold 196.97, copper 63.55
n
electrons per metal atom: 1 for gold from gold cyanide, 2 for copper from sulphate
F
Faraday constant, 96,485 C/mol
η
current efficiency (fraction of the current that plates metal)

Two useful constants follow directly, at 100% current efficiency. For gold from gold cyanide, Au(CN)₂⁻ + e⁻ → Au + 2 CN⁻, the deposit is 196.97 ÷ (1 × 96,485) × 3,600 = 7.35 g per ampere-hour. For copper from sulphate solution, Cu²⁺ + 2 e⁻ → Cu, it is 63.55 ÷ (2 × 96,485) × 3,600 = 1.19 g per ampere-hour.

Current efficiency and specific energy

η=mactualmtheoreticalSEC=Vcell×I×tmactual

where

mtheoretical
mass the current could plate at 100% efficiency (g)
SEC
specific energy consumption (Wh/g, the same as kWh/kg), with t in hours
Vcell
cell voltage (V)

Worked example: gold electrowinning cell

A cell operates at 1,500 A for 10 hours on eluate from carbon stripping. At 100% efficiency it could deposit 1,500 × 10 × 7.35 = 110 kg of gold. The gold actually recovered from the cathodes is 3.2 kg.

Current efficiency = 3.2 ÷ 110 = 2.9%.

This is normal for gold. Eluate is very dilute, typically tens to a few hundred milligrams of gold per litre, so gold ions reach the cathode slowly and most of the current drives side reactions, generating hydrogen from water and reducing dissolved oxygen. The relevant measure of performance in gold cells is not current efficiency but how completely gold is removed from the electrolyte on each pass. For that reason cells use high-surface-area steel wool or mesh cathodes and are operated until the spent electrolyte is low in gold.

At a cell voltage of 3.5 V, energy used = 3.5 × 1,500 × 10 = 52.5 kWh, or 52.5 ÷ 3.2 = 16 kWh per kilogram of gold. The power cost is minor relative to the value of the gold.

Worked example: copper tankhouse cell

A copper cell operates at 40,000 A with 92% current efficiency. Copper deposited per day = 40,000 × 24 × 1.19 × 0.92 = 1,047 kg.

At a cell voltage of 2.0 V, specific energy = 2.0 ÷ (1.19 × 0.92 ÷ 1,000) Wh/kg ≈ 1,830 kWh per tonne of copper. In a tankhouse, energy is a major cost, so each percentage point of current efficiency and each tenth of a volt is significant.

Current efficiency in two kinds of cellThe copper tankhouse example runs at 92% current efficiency; the gold eluate example at 2.9%.020406080100Copper tankhouse: 92.0%92.0%Copper tankhouseGold, eluate cell: 2.9%2.9%Gold, eluate cellCurrent efficiency (%)
Current efficiency in the two worked examples. Copper electrolyte is concentrated; gold eluate is very dilute, so most current drives side reactions. Illustrative figures.

Current efficiency losses in copper cells

Short circuits between anodes and cathodes, caused by nodules, bent plates or misalignment, pass current without depositing copper. Iron cycling also consumes current, as ferric iron is reduced to ferrous at the cathode and re-oxidised at the anode. Stray currents through leaks and wet cell tops add to the loss, and poor contacts on busbars and hanger bars raise voltage and generate heat.

Infrared surveys of the cell tops, current checks on individual cathodes and harvesting records are the routine means of locating these losses.

Gold cell operation

Gold in the electrolyte entering and leaving the cell, together with the barren eluate assay at the end of each cycle, is the measure of cell performance and should be tracked routinely. Cell voltage and current should be kept within the supplier's range, since excessive current density on dilute electrolyte mainly produces hydrogen and loose, powdery deposits. Gold sludge and loaded cathodes form part of gold in circuit and should be estimated at month-end. Electrowinning cells release hydrogen and other gases, so ventilation is a safety requirement.

Glossary

Electrowinning
Recovering metal from solution by passing direct current through it.
Cathode
The negative electrode, where metal ions gain electrons and plate out as metal.
Anode
The positive electrode, where water is split into oxygen and acid in most electrowinning cells.
Faraday constant
The electric charge carried by one mole of electrons: 96,485 coulombs.
Current efficiency
The fraction of the current that plates the wanted metal.
Specific energy
Electrical energy used per kilogram or tonne of metal plated.
Eluate
The gold-rich solution produced by stripping gold off loaded carbon.
Ampere-hour
One ampere flowing for one hour: 3,600 coulombs.

Frequently asked questions

How much gold does one ampere-hour deposit?

At 100% current efficiency, 7.35 g, because each gold ion requires one electron. In practice, gold cells operating on dilute eluate run at a current efficiency of a few per cent.

Why is current efficiency so low in gold electrowinning?

Gold eluate is very dilute, so gold ions reach the cathode slowly and most of the current produces hydrogen and reduces oxygen. Gold removal from the electrolyte, rather than current efficiency, is the measure of performance.

What current efficiency do copper tankhouses achieve?

Well-operated tankhouses commonly run at around 90% or higher. Short circuits, iron in the electrolyte and stray currents are the usual sources of loss.

How is electrowinning energy per tonne calculated?

Multiply cell voltage by current and by time in hours to obtain watt-hours, then divide by the metal deposited. For copper at 2.0 V and 92% efficiency the result is about 1,830 kWh per tonne.

Discuss your plant with a metallurgist

Tiegel is a Perth metallurgy company. We help with testwork, plant optimisation, metal accounting and investigations, and we build the Tiegel Suite software.

Talk to a metallurgist

References and further reading

  1. Marsden, J.O. and House, C.I. (2006). The Chemistry of Gold Extraction, 2nd edition. Society for Mining, Metallurgy and Exploration.
  2. Schlesinger, M.E., King, M.J., Sole, K.C. and Davenport, W.G. (2011). Extractive Metallurgy of Copper, 5th edition. Elsevier.
  3. Bard, A.J. and Faulkner, L.R. (2001). Electrochemical Methods: Fundamentals and Applications, 2nd edition. Wiley.

Worked examples and charts marked illustrative use invented figures, not data from any operation.